Tool Sign-Out Sheet Template WhoHasGear | Original manual recordkeeping aid | November 18, 2026 One sheet per tool crib per shift. Each tool or kit that leaves the crib gets its own line, so you can see who has it, where it went, which parts went with it, and what is still out when the shift ends. How to use: fill the crib and shift details, then write one line for each tool or kit as it is issued. Under Parts out, list every part that leaves with it and how many, for example: drill 1, battery 2, charger 1, case 1. When it comes back, count the parts again under Parts back, note the condition and sign the line in. At the end of the shift, check every line that is not Closed and complete the end-of-shift check. A tool kit is only back when every part is back. If one battery is missing, the line stays open even though the drill is on the shelf. A missing part can be formally reconciled without being found, but only through your organization's authorized resolution process, recorded in the exception log. A note saying “battery missing” is not enough. Condition out and Condition in are what the person at the crib can see, such as a cracked guard or a frayed cord. They are not a safety or operational inspection. If a tool comes back damaged, mark it Returned, tagged out and keep it off the shelf until the person your organization authorizes has inspected or cleared it. Use full dates and times. Keep earlier entries and add dated corrections with author and reason rather than overwriting them. Record only the borrower details your organization needs, and store completed sheets in an access-controlled place. This is a record, not a policy or a contract. It contains no fee, liability or discipline terms. Use your organization's own approved rules for those. This original worksheet has not been tested by operators. The completed example is fictional, not an organization's outcome. Source guide: https://whohasgear.com/blog/tool-sign-out-sheet-template Line status | Meaning on this sheet Closed | Every issued tool and part has been returned or formally reconciled through an approved, documented resolution; condition at return is recorded, the return is signed in, and no unresolved damage or other exception remains. Only authorized staff close a line. Open: parts missing | The tool is back but fewer parts came back than went out. The line stays open until the missing parts are back or authorized staff formally reconcile them through the organization's approved resolution process, recorded in the exception log. Open: overdue | Nothing has come back and the due-back time has passed. The end-of-shift check names a follow-up owner. Returned, tagged out | Everything is back, but damage or a fault was reported. The tool is not reissued until the organization's authorized person has inspected or cleared it. The exception stays open until authorized staff document the inspection outcome, any repair or clearance decision, and the resolution date. A tool must not be reissued unless it has been cleared for use. Missing tool | The tool itself has not come back and the borrower or the follow-up owner cannot say where it is. It goes in the exception log with its last recorded custody event. Blank crib and shift details Tool crib or storage location: ____________________ Date: ____________________ Shift (start and end time): ____________________ Crib staff on this shift: ____________________ Staff member doing the end-of-shift check: ____________________ Tools already out from an earlier shift (tool IDs): ____________________ Tools already tagged out before this shift (tool IDs): ____________________ Who to report missing or damaged tools to: ____________________ Blank tool sign-out register One line per tool or kit. Add rows as needed. Parts out and Parts back list each part with its quantity. Status: Closed / Open: parts missing / Open: overdue / Returned, tagged out / Missing tool. Tool ID / asset tag | Tool or kit | Parts out (qty) | Borrower | Job, site or work area | Condition out | Date / time out | Due back | Borrower initials | Parts back (qty) | Condition in | Date / time in | Received by | Status ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ Blank end-of-shift check Complete this before the crib closes or is handed to the next shift. Check every register line that is not Closed, including lines carried over from earlier shifts. End-of-shift item | Entry Lines opened this shift | ____ Lines closed this shift | ____ Open: parts missing (tool IDs and missing parts) | ____ Open: overdue (tool IDs) | ____ Returned, tagged out (tool IDs) | ____ Missing tool (tool IDs) | ____ Follow-up owner | ____ Next follow-up (date / time) | ____ Checked by (name and initials) | ____ Date / time of check | ____ Blank exception log One line per tool and per problem: parts missing, overdue, damaged and tagged out, or a missing tool. Keep the line until it has a resolution and a resolved date. Tool ID | Type (Parts missing / Overdue / Damaged, tagged out / Missing tool) | What is missing or what was seen | Last known borrower and location | Last recorded custody event | Reported by / when | Follow-up owner | Next follow-up | Resolution | Resolved date ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ | ____ Completed example: maintenance shop crib, day shift Fictional example. A five-person facilities maintenance team shares one tool crib. On November 18, 2026, the day shift runs 7:00 to 15:30 and R. Silva (fictional) runs the crib. Damaged tools are reported to the shop supervisor. Tool ID / asset tag | Tool or kit | Parts out (qty) | Borrower | Job, site or work area | Condition out | Date / time out | Due back | Borrower initials | Parts back (qty) | Condition in | Date / time in | Received by | Status DRL-04 | 18V drill kit | Drill 1, battery 2, charger 1, case 1 | J. Park | Building C restroom repair | No visible damage | Nov 18, 07:10 | Nov 18, 15:00 | JP | Drill 1, battery 1, charger 1, case 1 | No visible damage | Nov 18, 14:40 | RS | Open: parts missing SAW-02 | 7-1/4 in. circular saw | Saw 1, blade guard 1 | T. Reyes | Loading dock ramp | No visible damage | Nov 18, 07:25 | Nov 18, 15:00 | TR | Saw 1, blade guard 1 | Lower guard cracked and sticking | Nov 18, 13:55 | RS | Returned, tagged out LAS-01 | Cross-line laser kit | Laser 1, tripod 1, case 1 | M. Chen | Gym ceiling grid | No visible damage | Nov 18, 08:05 | Nov 18, 12:00 | MC | Laser 1, tripod 1, case 1 | No visible damage | Nov 18, 11:50 | RS | Closed Completed example: end-of-shift check End-of-shift item | Entry Lines opened this shift | 3 Lines closed this shift | 1 (LAS-01) Open: parts missing (tool IDs and missing parts) | DRL-04: 1 battery Open: overdue (tool IDs) | None Returned, tagged out (tool IDs) | SAW-02 Missing tool (tool IDs) | None Follow-up owner | R. Silva for DRL-04; shop supervisor for SAW-02 Next follow-up (date / time) | Nov 19, 07:30 Checked by (name and initials) | R. Silva, RS Date / time of check | Nov 18, 15:20 Completed example: exception log Tool ID | Type (Parts missing / Overdue / Damaged, tagged out / Missing tool) | What is missing or what was seen | Last known borrower and location | Last recorded custody event | Reported by / when | Follow-up owner | Next follow-up | Resolution | Resolved date DRL-04 | Parts missing | 1 of 2 batteries not returned | J. Park, Building C restroom repair | Kit returned to crib Nov 18, 14:40, received by RS | RS, Nov 18, 14:40 | R. Silva | Nov 19, 07:30: J. Park checks Building C and the van | Open | ____ SAW-02 | Damaged, tagged out | Lower blade guard cracked and sticking | T. Reyes, loading dock ramp | Saw returned to crib Nov 18, 13:55, received by RS | T. Reyes and RS, Nov 18, 13:55 | Shop supervisor | Nov 19, 07:30: inspection or clearance by the authorized person | Open: held off the shelf | ____ Completed example: why two lines are still open DRL-04 came back with one battery instead of two. The drill is on the shelf, but the Parts back count does not match Parts out, so the line stays Open: parts missing. Nobody writes Closed on DRL-04 until the second battery is back or authorized staff formally reconcile it through the organization's approved resolution process and record that in the exception log. SAW-02 came back complete, but the lower guard is cracked and sticking. Its status is Returned, tagged out, and it stays off the shelf until the authorized person has inspected or cleared it. Even when its custody record is eventually closed, it is only reissued if it has been cleared for use. LAS-01 came back with every part and no visible damage, so it is the only Closed line. The end-of-shift check names a follow-up owner and a next follow-up for each open line, so the next shift starts with the same two open items instead of a shelf that only looks complete.